Power Electronics Lab
Avail from us qualitative Power Electronics Lab. Complying
with the defined parameters of the industry, these products are ideal
for power electronics circuit experiments. These products find
applications in alarm circuit, lamp flasher, rectifiers, choppers and
inverter.
Technical Specifications:
DC power supply on board:
- ± 5V at 100mA
- ± 12V at 150mA
- ± 15V at 50mA
- ± 35V at 50mA
AC power supply on board:
- 18V - 0V - 18V at 50mA
- 15V - 0V - 15V at 50mA
- Triggering circuit on board: 5 gate signal output
- Frequency range: 40Hz to 900Hz Variable
- Amplitude: 12V
- PWM control of G1,G2,G3 and G4 duty cycle control of “Gate” signal is 0 to 100%
- Single phase rectifier: Firing angle control 0°-180° variables
- Firing circuit on board: Four gate signal output with isolation
- SCR assembly: 4 SCRs 2P4M, 600V,2A
- Power devices: IGBT-G4BC20S, MOSFET-IRF540, UJT-2N2646, DIAC-DB3, TRIAC-BT136, PUT-2N6027
- Circuit components on board: Capacitor 0.01uF, 0.047uF , 0.1uF, 0.33uF, 1uF/63V(4Nos.) 2.2uF/50V
- Diode 1N4007 (8Nos.)
- Zener Diode 9V (1Nos.)
- Inductors 10mH, (1Nos.), 68mH (2Nos.)
- Load resistance 120E, 270E, 1K, 2K2, each 5W
- Resistance on board (½ W) 22E/5W, 100E/2W, 220E/2W
- Resistance on board(1/4W) 10K (3Nos.), 22K,33K,47K,
- Potentio meter 4K7(2Mos.), 1M(1Nos.)
- Pulse transformer on board: 2 Nos. PT4502, 1:1 and one is PT4503 1:1:1
- Toggle switch: SPST (1Nos.)
- Power requirements: 220V ±10%, 50Hz
Experiments on board using breadboard:
- To study the characteristics of SCR and plot its V-I characteristics
- To study the gate control characteristics of SCR and It's graph
- To study the characteristics of UGT and calculate interbase resistance and intrinsic standoff ratio
- To study the characteristics of MOSFET
- To study the characteristics of IGBT
- To study the characteristics of DIAC and plot its V-I characteristics curve
- To study the V-I characteristics of TRIAC
- To study the characteristics of PUT
- To study of class B commutation circuit
- To study of class C commutation circuit
- To study of class D commutation circuit
- To study of class F commutation circuit
- To study the resistor triggering circuit
- To study the resistor-capacitor triggering circuit (Half wave)
- To study the resistor-capacitor triggering circuit (Full wave)
- To study the triggering of SCR using UJT
- To study the triggering of SCR using 555 IC
- To study the triggering of SCR using Op-Amp 74I IC
- To study of the ramp and pedestal triggering using anti-parallel SCR in AC load
- To study of the UJT relaxation oscillator
- To study of the voltage commutated chopper
- To study of the Bedford inverter
- To study of the single phase PWM inverter using MOSFET
- To study of the single phase PWM inverter using IGBT
- To study the half-wave controlled rectifier with resistive load
- To study the half wave controlled rectifier with RL load
- To study the full-wave controlled rectifier (mid-point configuration) with resistive load
- To study the full-wave controlled rectifier (mid point configuration) with RL load
- To study the fully controlled bridge rectifier with resistive load
- To study the fully controlled bridge rectifier with RL load